SerVision MVG 400 Uživatelská příručka Strana 156
- Strana / 190
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
SerVision MVG 400 System Guide
Resetting the Unit 156
3. Place the jumper on pins 2 and 3 of the RS232/485 connector.
Figure 149: Connectors for shorting activators and sensors
Figure 150: Jumper connected to pins 2 and 3
4. Reconnect the power to the unit. When the startup process is completed (the Power LED
on the front of the unit flashes at frequent intervals), the default factory settings are
restored.
5. Disconnect the power from the unit again.
6. Remove the jumper from the RS232/485 connector.
7. If you disconnected a PTZ controller before performing this procedure, reconnect the
controller.
8. Reconnect the power to the unit.
Erasing Recorded Video
Recorded video is normally stored on the hard drive until one of the following occurs:
• The video is over-written by newer video.
Pin 2 Pin 3
RS232/485
connector
- MVG 400 1
- Trademarks & Copyright 2
- Table of Contents 3
- Introduction 5
- The MVG 400 Package 6
- The MVG 400 Package 7 7
- Additional Equipment 8
- Additional Equipment 9 9
- Installing the Unit 11
- Diagram of the Rear Panel 12
- Connecting Cameras 15
- Connecting Sensors 17
- MVG 400 rear panel 18
- Sensors terminal block 18
- RS232 connector 21
- Connecting Activators 22
- Connecting Microphones 23
- About Speakers 23
- Connecting a CCTV Monitor 24
- To connect a CCTV monitor: 25
- Connecting the GPS Antenna 28
- Power LED 29
- Wire connector 30
- Connect to the 32
- Power connector 32
- Installing the MultiClient 33
- Opening the MultiClient 34
- Configuring the MVG 400 36
- Connection 37
- Configuring the MVG 400 38 38
- Login screen 38
- Overview of the Interface 39
- To open a summary screen: 40
- Configuring the MVG 400 42 42
- Main Menu, click 42
- Save Settings screen opens: 42
- Configuring the MVG 400 43 43
- Configuring the MVG 400 44 44
- Configuring the MVG 400 45 45
- Login screen opens 45
- System Settings 46
- General System Settings 47
- Configuring the MVG 400 48 48
- Configuring the MVG 400 52 52
- Update Now 53
- Configuring the MVG 400 54 54
- Configuring the MVG 400 55 55
- Setting the Unit Time 57
- Configuring the MVG 400 58 58
- Configuring the MVG 400 59 59
- Configuring the MVG 400 62 62
- LAN Settings 63
- Configuring the MVG 400 64 64
- IP in the cellular networ 65
- Cellular status 65
- Configuring the MVG 400 66 66
- Configuring the MVG 400 67 67
- Specifying the Access Point 68
- Configuring the MVG 400 69 69
- Current SSID 70
- Configuring the MVG 400 72 72
- Network Priorities 73
- Port Forwarding 74
- Configuring the MVG 400 75 75
- Proxy and DDNS Settings 76
- Configuring the MVG 400 79 79
- Authentication 80
- ", ', or `) 82
- Configuring the MVG 400 83 83
- SMS Message Templates 85
- Configuring the MVG 400 86 86
- Configuring the MVG 400 87 87
- Configuring the MVG 400 88 88
- Configuring the MVG 400 89 89
- Configuring the MVG 400 90 90
- Advanced 91
- Recorder Settings 91
- Configuring the MVG 400 92 92
- Configuring the MVG 400 93 93
- Configuring the MVG 400 94 94
- To disable AVV uploading: 95
- Camera Settings 96
- To configure a camera: 97
- Configuring the MVG 400 98 98
- Configuring the MVG 400 99 99
- as you view the 99
- Configuring PTZ 100
- Video Motion Detection (VMD) 101
- About VMD Regions 102
- About VMD Event Settings 102
- Configuring the MVG 400 103 103
- Configuring the MVG 400 104 104
- Configuring the MVG 400 105 105
- SMS and E-mail Notifications 106
- Automatically 106
- Field Description 107
- Configuring Video Lost 108
- Configuring the MVG 400 109 109
- AVV screen, in the 109
- Video Recording Settings 110
- Configuring the MVG 400 111 111
- Advanced Recorder Settings 112
- Configuring the MVG 400 113 113
- Configuring the MVG 400 114 114
- Camera Summary 114
- Configuring the MVG 400 115 115
- Configuring the MVG 400 116 116
- Sensor #1 116
- Configuring the MVG 400 118 118
- Field Description 119
- Configuring Sensor 4 to 121
- Control CCTV Display 121
- Configuring a CCTV Monitor 121
- (TV-Out) 121
- Configuring the MVG 400 122 122
- Outlines 124
- Creating an Outline 125
- Configuring the MVG 400 126 126
- Click to open Outline #1 127
- Camera #1 Settings 127
- Activating Outlines Manually 128
- Schedules 129
- Configuring the MVG 400 130 130
- Configuring the MVG 400 131 131
- Selected 132
- Configuring the MVG 400 133 133
- Defining Holiday Schedules 134
- Figure 122: Edit Holidays 135
- New Years Day 136
- Defining a New Schedule Row 138
- Saving Configuration Changes 139
- Configuring the MVG 400 140 140
- Discarding Changes 141
- Restoring Default Settings 142
- Configuring the MVG 400 143 143
- Restart Page 143
- Configuring the MVG 400 144 144
- Configuring the MVG 400 145 145
- Connecting to the MVG 400 146
- Figure 139: Viewing area 148
- Resetting the Unit 154
- Restoring Factory Settings 155
- Erasing Recorded Video 156
- Erase recorded video 157
- Resetting the Unit 158 158
- Main Menu 158
- Resetting the Unit 159 159
- Resetting the Unit 160 160
- Resetting the Unit 161 161
- Resetting the Unit 162 162
- Upgrading the Firmware 163
- Select firmware version from 164
- Required Files 165
- Upgrading the Firmware 166 166
- HVG/MVG/IPC Download Utility 166
- Upgrading the Firmware 167 167
- Catch Boot Option 168
- Catch Boot: 169
- –t after the file name 170
- -t added 170
- Upgrading Router Firmware 171
- System Diagnostics 173
- System Statistics 174
- Testing Remote Connections 175
- System Diagnostics 176 176
- System Diagnostics 177 177
- System Diagnostics 178 178
- Traceroute 179
- System Diagnostics 180 180
- Traceroute: 181
- System Diagnostics 182 182
- System Diagnostics 183 183
- System Diagnostics 184 184
- Troubleshooting 185
- Troubleshooting 187 187
- Troubleshooting 188 188
- Troubleshooting 189 189
- MVG 400 System Guide 190
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce